This fixes a bug in TRS vetting in lenient mode.

1. Improved scaler design uses field-based delinterlacer.
2. Added “3:2 Pull Down” control to Vid Out menu.
3. Added “3:2 Film Detect” status indicator to Vid In menu.
4. Implemented “Signal Loss” control in Vid Out menu.
5. Added support for Express Panel to be used for control of Proc settings and Audio gains.

Maintenance software version to support manufacturing

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

*Fixes issue accessing Salvo Edit pages.

*Fixed bug with RS232 control interface

1. Adds CRC and Checksum data integrity testing.
2. Changes auto reset time from 60 to 120 seconds.

1. Changes Reset time from 60 to 120 Secs
2. Added CRC Testing

Allows the use of the external GPI inputs to contribute the switch logic decision.

• Supports 50004501 board revision
• CRC/checksum error-detection added
• Support for self reference to input transport stream
• Minor bug fixes and improvements

• Supports 50004501 board revision
• CRC/checksum error-detection added
• Support for self reference to input transport stream
• Minor bug fixes and improvements

Use this file if updating from earlier version 2.x.x software. If updating from version 1.x.x, the 5030/5035 Kernel Update must be installed first.

• Adds support on touch screen for our newer 16 channel audio mixer cards.
• Adds new fan control, allows you to set the fan to Full.
• Allows setting and viewing Subnet Mask, Gateway and Distant IP addresses on the controller card. This will allow a 1RU frame to be used in remote sites.
• Removes Quick Access from the menu – no longer an option.

This file contains update instructions and kernel software.

Please read the instructions first!

This kernel software must be installed before the 5030/5035 System Control module or Table Top Touch Screen can be updated from 1.x.x to 2.x.x software.

Initial release.

Adds SNMP support and corrects a minor EDH promotion problem.

Initial release.

Initial release.

Corrects problem where the module would output NTSC when the SDI input was 625.

Corrects fault where module may signal present indication at power up when no signal is connected.

Adds extended GPI modes, and implements SNMP functionality.

Initial release of 5200 software in Version 2.0 compatible form.

Updated bit mapping for use of DP512 uProc.

Initial release of 5240 software in Version 2.0 compatible form.

Initial release of 5250 at 2.0-level software.

Initial release of 5280 software in Version 2.0 compatible form.

Initial release of 5300 software in Version 2.0 compatible form.

1. This fixes the component chroma problem
2. Maintenance software version to support manufacturing

Corrects contents of horizontal interval when using Frame Sync. Note: This update sets some Gains to zero. Reset Gains after updating.

Maintenance software version to support manufacturing

• Maintenance software version to support manufacturing

Maintenance software version to support manufacturing

Maintenance software version to support manufacturing

Initial release of 5380 software in Version 2.0 compatible form.

Maintenance software version to support manufacturing

Adds SNMP support for Ref Fail in the original Phase I SNMP interface. Adds support for 96kHz word clock through a menu control.

Initial release of 5405 software in Version 2.0 compatible form.

• Passes AFD
• Fixes incompatibility bug with newer controller software.

Corrects problem with RS232 communications.

Adds control for user to turn off EHD insertion.

1. Changes Reset time from 60 to 120 Secs
2. Added CRC Testing

This fixes a bug in TRS vetting in lenient mode.

• Full 2.0 support
• Adds SNMP functions
• Express panel support

Increased buffer size to handle non-standard embedding schemes.

Corrects possible distortion in Channel 4 output.

• Version change to include factory test procedures. No functional difference from v 1.1.0

• Improved crash logs
• Mac address visible on Web interface.
• OR 1425 MUST BE UPDATED TO 3.0.0+ WILL NOT WORK WITH OLDER SOFTWARE.

• Power up issues fixed when in mobile vehicle.
• Allows IP address and Subnet to be changed from front panel controls.

Prevents dim error LED under certain non-error conditions.

Initial software release.

Initial software release.

Update features:
1. Fixes issue with raster size.

1. Added CRC testing to the ASI/310 capable units.
2. Changed reset time control so it now has max of 120.0 seconds. Used to be 60.0 secs.

Additional HD formats supported.

Features:
Features:
1. Adds supports for HD ( High Capacity) SD cards.
2. Added Payload ID (VPID) to all formats.
3. Fixed bug with TimeCode from GPS on power up.

Features:

• Special Release notes for running version 2.2.7 software.

• Brings the module up to date for Ver2 system software functionality.
• Corrects errors in the original software where the test signal outputs were not always in zero time with the various reference inputs.

• Adds support for Higher capacity SD cards, SDHD.
• Need to use the current version of HDLogo converter 1.0.6.

• Bug fix – Module booted up in Secondary.
• Bug fix – keeps unit from loosing communication COMM ERROR
• Re-wored Dolby detection and handeling.
• Allows there to be a 3 frame difference between primary and secondary and still be considered identical.

**Must update AvenuePC to version 2.0.15 and 5030 controller software to 2.0.19 or later.

1. Changes Reset time from 60 to 120 Secs
2. Added CRC Testing

1. Changes Reset time from 60 to 120 Secs
2. Added CRC Testing

1. Changes Reset time from 60 to 120 Secs
2. Added CRC Testing

Required software update. Ensures stable sync output when switch is in secondary position.

• Adds SNMP support
• Corrects a LSB error

1. Fixed the AES parity error bug

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

Features:
Supports 2chan embedding

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

Update Features:
1. Fixes line in on left hand side of picture on composite out.
2. Fixed intermittent boot up issue, sometimes on boot up picture judder occurs.

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

1. Added new control in “Vid Out” menu called “Auto Black” which allows user to choose whether to output black or not when there is no input.

Suppress chroma for line 21 Closed Caption.

• NOTE: If circuit board is 45008500, advancing to this software version REQUIRES the module to be at ‘E’ Rev or later. If circuit board is 45008501 or later this software will work with any Rev level of the module.

Maintenance software version to support manufacturing

Features:
1. Adds supports for HD ( High Capacity) SD cards.
2. Added Payload ID (VPID) to all formats.
3. Fixed bug with TimeCode from GPS on power up.

• SNMP Support
• Added the ability to use Action panel and use Actions and Salvos.
• Multi-viewer support of Actions.
• YOU WILL NEED TO UPDATE YOUR 5825, LAYERING ENGINE CONTROL PANEL, FOR PROPER FUNCTIONALITY OF THE PANEL.

Important notes: All configurations will be lost after update if running v1.1.1 or earlier. Update 5830 control panel first if running 1.0.0, before updating the 9430 module.

1. Adds delay, milli seconds, in switching to secondary when primary fails. This was for
when Secondary was a duplicate of the primary but slightly delayed.
2. Fixed bug where board would sometimes stop running when AGC was running.

Required software update. Ensures stable sync output when switch is in secondary position.

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

Features:
1. Fixes bug in FIFO that caused loss of video output on occasions.
2. Added Audio and Video controls for Express Panel.
3. Added new menu control, Input Sync, Allows us to replace video input sync from gear that is not to spec.

1. Improved scaler design uses field-based delinterlacer.
2. Added “3:2 Pull Down” control to Vid Out menu.
3. Added “3:2 Film Detect” status indicator to Vid In menu.
4. Implemented “Signal Loss” control in Vid Out menu.
5. Added support for Express Panel to be used for control of Proc settings and Audio gains.

Changes to improve communication with other Avenue devices.

• Adds SNMP Support
• Adds ability to Download and Upload MV Layouts. .
• Added the ability to create and trigger actions from GPI, Web UI and 5835 Action Panel.
• Fixed bug where captions could reset the MV.

• Adds SNMP Support
• Adds ability to Download and Upload MV Layouts. .
• Added the ability to create and trigger actions from GPI, Web UI and 5835 Action Panel.
• Fixed bug where captions could reset the MV.